1. Tricone bits 1) Type: milled tooth bit and TCI bit 2) Size :3”-26”(76mm-660.4mm) 3) IADC: standard IADC including 111 to 737 4) Bearing sealed: metal sealed(HJ), rubber sealed(HA), not sealed(W) 5) Color: blue, golden or as customers’ requirement. Formation: soft, soft to medium hard, medium...
1. Tricone bits
1) Type: milled tooth bit and TCI bit
2) Size :3”-26”(76mm-660.4mm)
3) IADC: standard IADC including 111 to 737
4) Bearing sealed: metal sealed(HJ), rubber sealed(HA), not sealed(W)
5) Color: blue, golden or as customers’ requirement. Formation: soft, soft to medium hard, medium hard, hard, very hard
tricone drill bit
Generally bit diameters: 311mm,346mm,500mm,800mm,900mm and so on, all sizes could be customized by requirements.
Hole opener can enlarge a small well hole to bigger diameter in construction field, bridge construction, super highway construction, railway construction etc. This kind of bits are suitbale for different complex formation, shales, limestone, cobblestone and so on.
the hole opener always have multi-cones. Bit cones are splited from tricone bits and welded to bulid a big diameter bit, the pilot is attched with hole opener
2. Roller cone palm bit
Single cone bit is a kind of deceleration bit, which is the speed of cone is smaller than the speed of drill, mainly disorderly cutting broken rock. It is suitable for old well sidetracking and deepening the slim hole drilling operation under high rotary speed and drilling pressure.
1). Its application field is wide, not only suitable for side drilling, and can be used in deep well.
2). Work torque is lower than PDC bit in the same drilling pressure and formation condition. It can reduce the small size hole expansion buckling problems, so that avoid down hole accidents.
3). Single cone bit has advantages of both three cone bit and PDC bit, and make up the disadvantages of both. It is more suitable for large plastic formation than three cone bit, also can be applied to hard interlayer which PDC bit can not deal with other complex formation.
4). It can realize high speed and special drilling with down hole motor.
Elastomer sealed journal bearing
API Standard Pin
Medium to hard formations with low compressive strength and high drillability, such as mudstone, gypsum, salt, soft limestone, etc.
TRICONE BIT SPECIFICATION
WEIGHT IN BIT (KN/MM)
Low compressive strength, very aggressive and very soft formation: soft shale, clay, salina stone
Low compressive strength, very aggressive and very soft formation: shale, clay, soft limestone
Higher compressive strength, medium formation with interlayer: hard shale, sandstone, limestone
Higher compressive strength, medium formation with interlayer: hard shale, sandstone, gyprock
Soft formations with low compressive strength and high drillability, clay, mudstone, salt, soft shale
Soft to medium formations with high compressive strength, such as hard shale, limestone, sandstone
Soft to medium formations with high compressive strength, such as hard shale, limestone, sandstone, dolomite
Medium hard formation with high compressive strength, such as hard shale, limestone, sandstone, dolomite
Hard formation with high compressive strength, such as limestone, sandstone, dolomite, hard gypsum, marble
1. Cutting Structure of this type sealed and non-sealed tci tricone bits:
The wear-resistance of teeth is enhanced with premium tungsten carbide hard facing on the tooth surfaces for
steel tooth bit.
2. Gauge Structure of this type tci tricone rock bits:
Multiple gauge protection with gauge trimmers on the heel and gauge inserts on the gauge surface of the cone,
tungsten carbide inserts and hard facing on the shirttail increases gauge holding capability and bearing life.
3. Bearing Structure of this type tci tricone rock bits:
High precision roller bearing with two thrust faces. Ball locks the cone. Thrust faces hard face with wear resistant alloy.
Abrasion resistance and seizure resistance of the bearing are improved.
1. How to get an exact quotation?
Please try to send us what you want like these imformations:
-Tricone bits(Diameter, IADC code)
-PDC bits(Matrix or Steel body, blades quantity, cutter size, etc)
-Hole opener(Diameter, size of pilot hole, hardness of rocks, thread connection of your drill pipe, etc.)
-Roller cutters(Diameter of cones, model number, etc.)
-Core barrel(Diameter, quantity of cutters, connection, etc.)
Besides above, if possible please provide more information as below:
Drilling depth in vertical well drilling, Drilling length in HDD, hardness of rocks, Capacity of drill rigs, application(oil/gas well drilling, or water well drilling, or HDD, or foundation).
Incoterm: FOB or CIF or CFR, by plane or ship, port of destination/discharge.
2. What is the quality control for your products?
=>All of our production are in lines of API rules and ISO9001:2015 strictly, from signing contract , to raw materials, to each production processes, to product finish, to after-sale service, each processes and sections are in accordant with standard.
3. About lead time, payment terms, delivery ?
=> We always have regular models available in stock, prompt delivery is one of our advantages. Mass production depends on quantity of order.
We accept all regular payment terms including L/C, T/T, etc.
We are near with the biggest Asia port Shanghai Yangshan port and Pudong airport, transportation from our factory to to these place only takes one day, fast and very economical inland charges.